This is my first attempt at this so I wasn't surprised to see a complete breakdown of the screen.
I am using Ulano Proclaim (blue) (Came with a starter package I ordered) on 110 mesh. Went with 1 coat on each side.
I used a homemade exposure unit consisting of 4 24" 20w bulbs (they say GE sunshine F-20) lights are about 3 inches from the glass.
Went for 5 minutes.
Washed it out with a light spray, no more than 2 or 3 minutes, water was cold from an outdoor source and as soon as I could see my image it was a fuzzy melting mess. Even the edges of my positive started to wash out.
I am assuming I just overexposed the hell out of it, but just wanted to hear if anyone has some advice.
Thanks
Screen Problems
Moderator: Moderator Team
- yaleteamsandtees
- Administrator
- Posts: 145
- Joined: Thu May 18, 2006 11:00 am
- Location: Gaithersburg, Maryland
-
- Just Browsing
- Posts: 7
- Joined: Wed Jan 10, 2007 9:14 pm
- yaleteamsandtees
- Administrator
- Posts: 145
- Joined: Thu May 18, 2006 11:00 am
- Location: Gaithersburg, Maryland
Now ya see what happens when ya read a post ina hurry!!
Sorry.
The exposed areas stayed right?
(The areas outside the image)
The image edges were fuzzy.
The larger areas washed out OK.
Then, yes you over exposed it.
Also not knowing how dense your posi is can be a bit a of a problem.
Vellum?
Inkjet?
You also will experience undercutting with tube fluorescent lights.
We use unfiltered black lights (tubes) and burn for 90 seconds.
-Rob
Sorry.
The exposed areas stayed right?
(The areas outside the image)
The image edges were fuzzy.
The larger areas washed out OK.
Then, yes you over exposed it.
Also not knowing how dense your posi is can be a bit a of a problem.
Vellum?
Inkjet?
You also will experience undercutting with tube fluorescent lights.
We use unfiltered black lights (tubes) and burn for 90 seconds.
-Rob
-
- Just Browsing
- Posts: 7
- Joined: Wed Jan 10, 2007 9:14 pm
90 seconds wow.
Yeah, I looked up some things and I think I am having an undercutting problem. I think the tubes are a little too close to the glass which I will adjust.
I am just using an inkjet film positive.
Yes, for the most part the exposed areas stayed correct, there was some peeling and melting kinda thing going on- not sure if this would be from over exposure or my coating or what, but most of it was just around the corners of the screen which I would've caught with some blockout tape anyway.
I'm assuming the lights I am using are "grow lights"
So I guess the question is, stick with this and mess with it till I figure it out? Or make some adjustments and just get a 1000 watt single bulb?
Yeah, I looked up some things and I think I am having an undercutting problem. I think the tubes are a little too close to the glass which I will adjust.
I am just using an inkjet film positive.
Yes, for the most part the exposed areas stayed correct, there was some peeling and melting kinda thing going on- not sure if this would be from over exposure or my coating or what, but most of it was just around the corners of the screen which I would've caught with some blockout tape anyway.
I'm assuming the lights I am using are "grow lights"
So I guess the question is, stick with this and mess with it till I figure it out? Or make some adjustments and just get a 1000 watt single bulb?
- yaleteamsandtees
- Administrator
- Posts: 145
- Joined: Thu May 18, 2006 11:00 am
- Location: Gaithersburg, Maryland
-
- Just Browsing
- Posts: 7
- Joined: Wed Jan 10, 2007 9:14 pm
- MosquitoLane
- Just Browsing
- Posts: 2
- Joined: Sat Feb 24, 2007 8:09 pm
here's what I do...
I also use it. Go to the ulano website and you can download the tech sheets. It has an exposure time thingy. I just go 10 minutes and it works out. I have the UV tubes about 6 inches away. One coat on each side ...well side last. Hope it works out I have wasted much time trying to get it write...step wedge test??? don't have time LOL... OH AND make sure your screen has dried completely before you expose. ALSO...I have a piece of foam that I set in the well over the image area and I stack t-shirts on top of it to weigh it down.