Reclaiming screens

Post your questions, suggestions, ideas and advice to issues you have run into in your screen printing shop.

Moderator: Moderator Team

Post Reply
Pierre
Just Browsing
Just Browsing
Posts: 2
Joined: Thu May 11, 2006 6:56 pm
Location: Pitman NJ

Reclaiming screens

Post by Pierre »

Hey Guys !!!

I reclaim my screens, but sometimes I have a haze that I cannot get rid of !!
I de-haze again and still , it is still there !!!
Any suggestion to get rid of the haze ???

Thank you

Pierre
User avatar
jpied
Just Browsing
Just Browsing
Posts: 11
Joined: Thu May 11, 2006 7:27 pm
Location: Texas

Post by jpied »

Plastisol Ink?
KAISER SULTAN
Just Browsing
Just Browsing
Posts: 2
Joined: Fri May 12, 2006 1:37 pm

Post by KAISER SULTAN »

Haze appears due to two reasons:
1: The pigment in the ink or emulsion causes the haze
2: The uncured emulsion once comes in contact with some harsh press wash or ink Degradent, leaves a permanent coalesced film.

The 2nd.type of haze can not be eliminated.
The 1st.type of haze may be removed by using an inkgradent. If that does not work than you may use haze removers available in the market place.

KAISER
User avatar
jpied
Just Browsing
Just Browsing
Posts: 11
Joined: Thu May 11, 2006 7:27 pm
Location: Texas

Post by jpied »

Use HR-30 (CCI)as a third step before you apply your degreaser.
1.Degradent
2.Emusion Remover
3.*HR 30
4.Degreaser

It may not remove all of the coalesced film stain he's talking about, but
I guarantee you it will remove 95% of it,if your using plastisol that is,non toxic also.
KAISER SULTAN
Just Browsing
Just Browsing
Posts: 2
Joined: Fri May 12, 2006 1:37 pm

Post by KAISER SULTAN »

The sequence of procedure described is correct. There are inkdegradents that are ink & emulsion remover and act as degreaser. The coalesced film can not be completely eliminated by a strong caustic solution, combined with surfactants and solvents. The imbedded portion of the coalesced film in the screen is such that if you let caustic solution stand for too long, it attacks the filament in the mesh. The other problem is the time consumed and exposure to harsh chemicals is not worth it. You are better off to re-mesh the screen for $7.00.
KAISER
User avatar
jpied
Just Browsing
Just Browsing
Posts: 11
Joined: Thu May 11, 2006 7:27 pm
Location: Texas

Post by jpied »

HR 30 isn't caustic and you don't have to let it sit, you spray it on, inside and out, then scrub, then powerwash it out...simple...and alot less time
than restretching mesh that's for sure.
User avatar
d fleming
Moderator
Moderator
Posts: 546
Joined: Mon Apr 03, 2006 3:33 pm

Post by d fleming »

I never really have bad haze problems with my t-shirt screens or plastisol. Now my big screens are a different story and they are more like 60-80 bucks a piece to stretch new fabric in. Corogloss can leave some rsidue and god forbid you don't properly clean a screen after printing metal all day with catalyzed ink. I use GB 2000 ink stain and haze remover from Nazdar. Works pretty well.
improperazzi.net
Just Browsing
Just Browsing
Posts: 4
Joined: Tue May 16, 2006 6:12 pm
Location: Las Vegas
Contact:

Does a haze of an image cause problems with a new stencil?

Post by improperazzi.net »

I have some screens with ink images left from watercolor ink as well as plastisol. It didn't really seem to matter until I tried to burn a high resolution image onto it. Is that why image haze is unwanted?

Thanks!
iNVASiON iNC.
distributors of
iMPROPERAZZi
DESIGNS

www.improperazzi.net
User avatar
ROADSIDE
Administrator
Administrator
Posts: 458
Joined: Fri Feb 24, 2006 4:36 pm
Location: South Jersey
Contact:

Post by ROADSIDE »

I have only has hazing problems when I got lazy and didnt clean the screens for like a month of two.
.... I can give you my opinion but I can't tell you if it's right or not.
Post Reply